Technical Reference
Early-age concrete strength — how it is specified, how it is estimated, and how it is tested. Maturity is one method within that, not the whole of it.
What this covers, and what it is called
This began as a reference on concrete maturity and outgrew the label. Several pages here are not about maturity at all and say so explicitly: rebound hammer testing is a different method under different standards; compliance age is a question of specification under BS EN 206 and BS 8500; the seven-day ratio is a property of cement class under Eurocode 2. Filing those under "concrete maturity" would repeat the category error the reference exists to correct.
The scope is early-age concrete strength, in three parts — how it is specified, how it is estimated, and how it is tested. Maturity is one estimation method within that.
Start here
Compliance age
Why 28 days is a reference age rather than an endpoint, and when BS 8500 permits 56.
Read the guide →What is maturity?
The temperature–time calculation, what the index represents, and what it cannot tell you.
Read the guide →Low-carbon binders
Why binder chemistry changes the temperature sensitivity every maturity function assumes.
Read the guide →Common misconceptions
75% at seven days? Full strength at 28 days? Rebound hammer? Cubes?
Browse the FAQ →The method in one diagram
The important distinction is between calculating maturity and calibrating strength against maturity. ASTM C1074 requires establishing the strength–maturity relationship for the concrete mixture and recording the temperature history of the concrete for which strength is to be estimated.
Temperature history is not the whole picture
Because temperature is the only quantity measured in the structure, the record on its own carries no confirmation that the concrete placed was batched as intended. Carino and Lew put it directly: a batching error — an over-dosed retarder, an unintended change in cement replacement — produces a perfectly normal-looking temperature curve.
ASTM C1074 addresses this twice. Clause 5.3 lists it among the method's major limitations: the method needs supplementing by other indications of the potential strength of the concrete. Clause 9.5 then makes it procedural — before critical operations such as formwork removal or post-tensioning, the maturity determination is to be supplemented with other tests confirming that the concrete in the structure has a potential strength similar to the concrete the relationship was built on.
What that clause asks for is often misread as re-calibration. It is not. The strength–maturity relationship is established once for a mixture and is not rebuilt pour by pour; what 9.5 confirms is the concrete as delivered, and the routes it names are in-place strength tests, early-age tests on standard-cured specimens, or accelerated-cured specimens. On a UK job much of that evidence is already being generated by conformity and identity testing under BS EN 206 and BS 8500, so the practical question is usually whether those results are read against the maturity estimates or filed separately from them.
Which standards apply
| Question | Primary document |
|---|---|
| How is the maturity method applied? | ASTM C1074 |
| What in-place methods exist and what are their limits? | ACI 228.1R-19 |
| How is in-situ compressive strength assessed in UK/European practice? | BS EN 13791 |
| How is concrete specified and its strength class defined? | BS EN 206 |
| How are execution requirements, including striking, set? | BS EN 13670 |
Claims this reference addresses
Each page states the proposition it is answering before answering it. The propositions are stated in general terms rather than quoted, because they circulate as common shorthand rather than as any one source's wording.
| Claim | Position |
|---|---|
| A maturity sensor measures the strength of the concrete it is embedded in. | Not as stated — it measures temperature. More |
| A rebound hammer measures concrete maturity. | Incorrect. More |
| Cube results tell you the maturity of the concrete. | Incorrect. More |
| Concrete reaches about 75% of its 28-day strength at seven days. | A crude rule of thumb, not far off at seven days (68–82% by cement class); unreliable earlier. More |
| Concrete reaches its full strength at 28 days. | Incorrect. More |
| A well-fitting strength–maturity curve proves the maturity calculation is sound. | Does not follow. More |
| Once a mix is calibrated the system can be relied on for that mix. | Incomplete. More |
| Which maturity function is used is an implementation detail. | Incorrect. More |
| Low-carbon concrete cannot be reliably maturity monitored — or, conversely, any mix is fine if the sensor has a curve. | Both wrong. More |
| Maturity monitoring measures in-situ strength in real time. | Overstated. More |
Full contents
Grouped by the three questions above rather than by method, because several pages sit in more than one.
Specified
What the design and the contract actually ask for, and at what age.
Compliance age — 28 days, and when 56 is permitted
Seven-day strength and the 75% rule
Low-carbon binders and slow cements
Estimated
Working out the strength of concrete in the structure without breaking it.
What is concrete maturity?
Maturity index vs strength–maturity relationship
Establishing the relationship
Maturity functions: Nurse–Saul and Arrhenius
Limitations of the maturity method
Quick answers
FAQ — short answers on terminology, maturity functions, compliance age, applicable standards and what the method cannot do.
References
- Standard ASTM C1074-19e1 — Standard Practice for Estimating Concrete Strength by the Maturity Method.
- Report ACI 228.1R-19 — Report on Methods for Estimating In-Place Concrete Strength.
- Standard BS EN 13791:2019 — Assessment of in-situ compressive strength in structures and precast concrete components.
- Standard BS EN 206 — Concrete. Specification, performance, production and conformity.
- Standard BS EN 13670 — Execution of concrete structures.
- Paper Carino, N. J. and Lew, H. S. (2001) — The Maturity Method: From Theory to Application. Proceedings of the 2001 Structures Congress & Exposition, ASCE.
Standards are cited by identifier and title. Consult the current licensed standard text before making project decisions. Publisher links were verified on 11 August 2026 and should be rechecked before publication.
Content and sources last reviewed 11 August 2026.