OTB Technical Reference

Concrete Maturity FAQ

Short version: maturity is a temperature-history index used with a mix-specific strength–maturity relationship to estimate in-situ strength, subject to independent verification.

Frequently asked questions

Does a Schmidt hammer measure maturity?

No. A Schmidt/rebound hammer measures rebound number, associated with surface hardness, under BS EN 12504-2. Maturity is calculated from temperature history and time under ASTM C1074.

Do concrete cubes measure maturity?

No. Cubes provide compressive-strength measurements under BS EN 12390-3. Their results can be combined with maturity data to establish a strength–maturity relationship.

Does concrete reach 75% of its 28-day strength at seven days?

It is a crude rule of thumb, and at seven days it is not far off. Eurocode 2's strength-development expression gives 82% for a Class R cement, 78% for Class N and 68% for Class S at 20 °C, so 75% sits mid-range. The figure becomes unreliable earlier: at three days the same three classes span 46–66%, and at two days 35–58%.

If the 75% figure is about right, why not use it?

Because the ages where it is accurate are not the ages where decisions are made. The spread between cement classes is 13 points at seven days but 20 at three days and 23 at two — and striking, backpropping and load application happen in that early window. A ratio also cannot give an absolute strength, because the 28-day strength of that particular batch is not yet known.

Does concrete reach full strength at 28 days?

No. Twenty-eight days is a common reference or specified age under BS EN 206, not a universal ultimate-strength endpoint. Strength continues to develop beyond it.

What is a maturity index?

A numerical index calculated from the concrete's temperature history using a maturity function, expressed either as a temperature–time factor or as equivalent age at a specified temperature.

What is a strength–maturity relationship?

A mix-specific relationship between measured compressive strength and calculated maturity index, established in the laboratory before field use.

Is maturity the same as strength?

No. Maturity is used to estimate strength through a calibrated relationship.

What is the Nurse–Saul method?

A temperature–time factor approach, originating in British research published in 1949 and 1951, that accumulates temperature above a selected datum temperature.

What is the Arrhenius method?

An equivalent-age approach, proposed by Freiesleben Hansen and Pedersen in 1977, that models the temperature dependence of the rate of strength development using a Q or apparent activation-energy parameter.

Which maturity function should be used?

There is no single function applicable to all mixtures. The appropriate one depends on how the rate of strength gain for that mixture varies with curing temperature, which can be measured.

What reference temperature is used for equivalent age?

Conventionally 20 °C in European practice and 23 °C in North American practice. An equivalent age is ambiguous unless the reference temperature is stated.

Does low-carbon concrete invalidate maturity monitoring?

No, but changes in binder chemistry alter hydration kinetics and temperature sensitivity, making appropriate calibration and parameter selection especially important.

What is the crossover effect?

At equal maturity, concrete cured at higher early-age temperatures reaches higher early strength but lower long-term strength than the same concrete cured cooler. It is an inherent limitation of the method.

Can maturity detect poor compaction?

No. Maturity indicates the strength expected from the monitored thermal history. It does not detect placement defects.

Can maturity monitoring predict peak temperature or thermal cracking risk?

No. It is retrospective — it computes an index from a temperature history that has already occurred. Estimating peak temperature and cracking risk before placing is a separate exercise using heat-of-hydration modelling, and is what allows the mix or method to be changed in time. CIRIA C766 covers restrained-deformation cracking.

Can maturity confirm the concrete was batched correctly?

No. Temperature history carries no information about mix proportions. ASTM C1074 lists this among the method's limitations at clause 5.3, and at clause 9.5 directs that before critical operations such as formwork removal or post-tensioning the maturity determination be supplemented with other tests confirming the concrete in the structure has a potential strength similar to the concrete the relationship was built on. That is a check on the concrete as delivered, not a recalibration — see the next answer.

Does the mix have to be re-calibrated for every pour?

No. The strength–maturity relationship is developed once in the laboratory for a mixture and remains valid while that mixture does; it is re-established when constituents, proportions or production practice change materially. What clause 9.5 asks for before a critical operation is confirmation of the concrete as delivered, and on most UK jobs the conformity and identity testing already running under BS EN 206 and BS 8500 supplies much of that evidence.

Can maturity replace all cube or cylinder testing?

Not as a blanket proposition. The method requires a laboratory strength–maturity relationship and remains subject to verification and project requirements.

Can concrete strength be specified at 56 days?

Yes. BS 8500-1 permits compressive strength to be specified at 56 days, which suits slower binder systems. The Concrete Centre estimates a saving of roughly 15–20 kg/m³ of cement and 5–10 kg/m³ of embodied carbon for a Class S cement concrete specified at 56 rather than 28 days.

Does specifying at 56 days relax cover requirements?

No. Where strength is specified beyond 28 days, cover is assessed against the characteristic strength the concrete will reach at 28 days.

What are cement Classes R, N and S?

Eurocode 2's classification of cements by rate of strength gain — R fastest, N intermediate, S slowest. CIRIA C766 maps cement types to these classes. High-replacement low-carbon mixes are typically Class S.

Does maturity monitoring replace 56-day conformity testing?

No. Conformity at 56 days and early-age strength for striking are different questions. Maturity monitoring addresses the second; it is not a conformity method.

How accurate is the maturity method?

ASTM C1074 declines to say. Clause 10.1 records that estimated strength depends on the appropriateness of the maturity function, the early-age temperature history and the actual mixture proportions, and concludes that no statement of precision and bias can be written. An accuracy figure quoted for a maturity system describes that implementation under stated conditions, not the method.

Can a maturity instrument display the wrong maturity index?

Yes, and the standard says so. Instruments apply built-in values of datum temperature or activation energy, so the index displayed may not be the true value for the mixture being monitored. Temperature–time readings can be corrected for a wrong datum temperature; equivalent-age readings cannot be corrected after the fact for activation energy.

Where does ASTM C1074 give parameter values?

Approximate values of datum temperature and Q are in Appendix X1, stated for Type I cement without admixtures. Mixture-specific values are determined experimentally under Annex A1, which is mandatory information within the standard — the approximations are the concession, not the procedure.

Which standards apply in the UK?

ASTM C1074 for the maturity method itself; BS EN 206 for specification and strength classes; BS EN 13670 for execution; BS EN 12390-2 and -3 for specimen strength testing; BS EN 13791 and BS EN 12504-2 where in-situ assessment by other methods is involved.

Related pages

What is concrete maturity? Limitations of the maturity method Nurse–Saul vs Arrhenius maturity functions Maturity and low-carbon concrete

References

Standards are cited by identifier and title. Consult the current licensed standard text before making project decisions. Publisher links were verified on 11 August 2026 and should be rechecked before publication.

Content and sources last reviewed 11 August 2026.