How Is a Concrete Strength–Maturity Relationship Established?
Once a mix has been calibrated, the system can be relied on for that mix from then on.
Incomplete. Calibration establishes the relationship. It does not confirm that the concrete delivered on any given day matches the mix that was calibrated — which is why the standard treats the method as needing to be supplemented by other evidence of strength, not why it needs recalibrating each pour.Laboratory stage
- Prepare at least 15 cylindrical specimens, with mixture proportions and constituents similar to those of the concrete whose strength is to be estimated.
- Embed temperature sensors in at least two specimens and record the temperature history used to calculate maturity.
- Cure the specimens in a water bath or moist room and test for compressive strength at a series of ages — ASTM C1074 uses 1, 3, 7, 14 and 28 days, on at least two specimens per age.
- Record the average maturity index at each test point.
- Plot measured strength against maturity index, then fit and assess an appropriate relationship.
Field stage
- Install temperature sensors as soon as practicable after placement, at locations critical in terms of exposure and structural requirements.
- Record the temperature history of the concrete in the structure.
- Calculate maturity using the selected maturity function.
- Apply the established strength–maturity relationship.
- Report the result as an estimated in-situ strength, subject to the method's assumptions and limitations.
Sensor placement carries more weight than it is usually given. The estimate applies to the concrete at the sensor, and a reading taken away from the critical location may not represent the element that governs the decision.
What should remain consistent?
The field concrete must be representative of the mixture used to establish the relationship. ASTM C1074 requires the strength–maturity relationship to be established for the concrete mixture concerned, using its actual proportions and constituents.
Verification is part of the method, not an optional extra
Temperature history is the only quantity measured in the field, and it carries no information about whether the concrete delivered had the intended proportions. Carino and Lew describe the consequence of ignoring this as potentially drastic, precisely because undetected batching errors — excessive cement replacement, over-dosed retarder — leave no signature in the temperature record.
ASTM C1074 lists this among the method's major limitations at clause 5.3, and turns it into a procedural step at clause 9.5: before critical operations such as formwork removal or post-tensioning, the maturity determination is to be supplemented with other tests confirming that the concrete in the structure has a potential strength similar to that of the concrete used to develop the relationship.
This is not re-calibration
The distinction matters and is regularly lost. Clause 9.5 does not ask for the strength–maturity relationship to be re-established. That relationship is developed once for a mixture, in the laboratory, and stays valid while the mixture does. What 9.5 confirms is the concrete as delivered — that what went into the structure has the potential strength of what was calibrated. Re-establishing the relationship is a separate matter, triggered by material change in constituents, proportions or production practice.
Nor does it usually mean commissioning bespoke tests. On a UK job the conformity and identity testing under BS EN 206 and BS 8500 is already producing much of this evidence; the discipline that costs nothing is reading it against the maturity estimates rather than filing the two records apart.
The routes clause 9.5 names
Where a single operation carries real consequence — stressing, striking a transfer slab, terminating cold-weather protection — the standard identifies three acceptable forms of supplementary evidence:
- in-place tests giving an indication of strength — the standard names penetration resistance, cast-in-place cylinders, pullout and break-off methods;
- early-age compressive strength tests on standard-cured specimens moulded from samples of the concrete as delivered; or
- compressive strength tests on specimens moulded from the as-delivered concrete and accelerated-cured.
ASTM C1074 clauses 9.5.1 to 9.5.3. Note that the second and third routes sample the concrete as delivered, not cores taken from the hardened structure.
When to re-establish the relationship
Periodic comparison with conventional strength tests provides confidence that the relationship remains appropriate. Where materials, proportions, curing conditions or production practices change materially, the relationship should be reviewed and, where appropriate, re-established. In UK practice this sits alongside the execution requirements of BS EN 13670 and the specification basis of BS EN 206.
Related pages
References
- Standard ASTM C1074-19e1 — Standard Practice for Estimating Concrete Strength by the Maturity Method.
- Paper Carino, N. J. and Lew, H. S. (2001) — The Maturity Method: From Theory to Application. Proceedings of the 2001 Structures Congress & Exposition, ASCE.
- Standard BS EN 13670 — Execution of concrete structures.
- Standard BS EN 12390-2 — Testing hardened concrete. Making and curing specimens for strength tests.
- Standard BS EN 206 — Concrete. Specification, performance, production and conformity.
Standards are cited by identifier and title. Consult the current licensed standard text before making project decisions. Publisher links were verified on 11 August 2026 and should be rechecked before publication.
Content and sources last reviewed 11 August 2026.